E’LINESMAN

Reg No: 84/10770/07

Suppliers and manufactures of transmission line stringing equipment, compression fittings and hardware for transmission lines

 
 

HOME

ABOUT US

CONTACT US

IZUMI TOOLS

FITTINGS

STRINGING

ENQUIRY

 

 

 

 

 

 
 

 

We offer a full range of Aluminium, Copper and friction welded Bi-metal compression and mechanical connectors for overhead lines from L.V. to EHV applications for both "Die-less" and "Die" compression systems. We also manufacture a range of Sub Station clamps and Sub Station Bus Bars. 

wpe70.jpg (5161 bytes)

NON-TENSION JOINTS:
Used on all types of aluminium conductors including alloy and steel reinforced (A.C.S.R) Also steel for use at jumper stations.

TAP CONNECTORS TEE OFF CRIMPING TYPE:
Aluminium two part split tube, sliding fit connectors, grease filled and individually packed with welded Aluminium Tubular tap. Suitable for all types of Aluminium conductors.

wpe76.jpg (4506 bytes)

ALUMINIUM LUGS:
Hole size 12, 16 and 20mm dia. as standard.  Other sizes supplied on request.  Terminal lugs are available for solid Aluminium core cables (S.A.C) and all forms of stranded conductor.

BI-METAL LUGS:
Friction welded aluminium to copper / copper to aluminium.  Factory fitted brass insert providing effective anti-corrosion barrier between dissimilar metal contact faces.  General termination duties where connections are made to Copper Bus Bars or apparatus terminal studs when bimetal contacts with the aluminium lug palm requires to be avoided.

MIDSPAN JOINT: TWO PIECE
Used on all types of aluminium conductors including alloy  and steel reinforced (A.C.S.R) rated 95% conductor ultimate tensile strength.

DEAD ENDS
Supplied with high tensile active bolts, nuts and washers, for direct mounting to Anchor Clamp flag.

JUMPER TERMINAL (2 X HOLE LUG) WITH 2 ALUMINIUM BOLTS
All aluminium lugs used as general termination onto dead end flags or similar applications.  Machine skimmed contact faces.  Used on all types of aluminium conductors including Alloy and Steel Reinforced (A.C.S.R).
NOTE: can be provided with single hole or three holes of varying diameter on request .  compression part of lug can be angles up to 30 i.e. Code A.L. 15 or code A.L. 30.

TAP CONNECTOR TEE-OFF FLAG TYPE WITH BOLTED JUMPER TERMINAL (2 HOLE LUG)
Aluminium two part split tube, sliding fit connectors, grease filled and individually packed, with welded aluminium flag.  Suitable for all types of aluminium conductors.
NOTE: Orientation of flag shown 90 to conductor axis.  Flag can be orientated up to 30 in longitudinal or transverse plan by special request.  Flag designed to accommodate lug code A.L.
REPAIR SLEEVE FOR ALUMINIUM CONDUCTORS
A.R.S. Connectors are used for restoring full conductivity to frayed or slightly damaged strands.  The device does restore full mechanical strength in the case where conductor strands are broken.

"C" CONNECTOR ALUMINIUM OR COPPER
The range of combinations is extensive and many varied conductor sizes in solid and stranded inclusive of main and service cable can be jointed.

 

ANGLE TAP CONNECTOR (OPEN THROAT) FORGED ALUMINUM AND COPPER

A.T.C. connectors are suitable for all types of aluminium and Copper conductors and cables, jumpers and feeders.

wpe7.jpg (8889 bytes) wpe1A.gif (11298 bytes) wpe14.jpg (7291 bytes) wpe18.jpg (9143 bytes)
BTC 1.1    10-35mm2 BTC 2.3     35-70mm2 ATC 3.2      70-95mm2 CTC 3.4      120mm2

 

Back to Top

 

 

     

 


 
 
 

 

 
 

ABOUT US  CONTACT US  IZUMI TOOL RANGE  FITTINGS  STRINGING EQUIPMENT  ENQUIRY

Copyright © 2013 by E'Linesman (PTY) LTD. All rights reserved.